The SB10 is a powered 10" sub-bass designed to complement all of the full-range monitors in the S-Series. The SB10 will extend the system frequency response down to 20 Hz and increase the system's maximum spl. The filter bypass on the left channel optimises the SB10's performance when it is used as a dedicated LFE monitor in a multi-channel system. With the 2-in 2-out bass management, a single SB10 can reinforce a stereo pair of full range cabinets.
... A long throw 10" cast chassis driver is mounted in a tuned cabinet constructed of ash veneered 26 mm MDF. Tradition is broken in that the matched 215W RMS amplifier and 2-channel SB10 controller are housed in a separate, single 1U rack space unit. Due to this Remote Power, the electronics do not suffer the adverse effects caused by the LF vibrations that are created by the drive unit. Calibration and operation of the SB10 controller are easily achieved in comfort with the unit sited close to hand.
SB 10 Technical Specification
Dimensions (w x h x d) 617 x 333 x 290
Weight 19.8 kg
Driver Bass cone 1 x 250 mm (10")
Frequency Response Set by controller
Input Connector 1 pair gold plated binding posts
Nominal Impedance 3.3 Ohm
Maximum SPL 113 dB (c) continuous pink noise @1m (127 dB (c) per pair RMS music)
Sensitivity Dependent on controller settings
SB Controller Technical Specification
Dimensions SB Controller - 1U case 270 mm deep
Weight SB Controller - 5.5 kg
Input
Connector 2 off XLR and 1/4 inch jack combo socket
Impedance 10k electronically balanced
Wiring Pin 1 (Sleeve) ground, Pin 2 (Tip) hot, Pin 3 (Ring) cold
Gain -14 dBu to +6 dBu
Outputs
Left and right monitor outputs 2 off XLR3 type male left & right
Impedance <100 ohm electronically balanced
Wiring Pin 1 ground, Pin 2 hot, Pin 3 cold
Sub Bass output 1 pair binding posts
Filters
Left & right input summed to sub output
Subsonic/High pass -3dB @ 14 Hz, 24dB/oct or -3dB @ 28 Hz, 24dB/oct (set by internal jumper)
Low Pass -3dB @ 40 Hz to 135 Hz, externally adjustable @ 24db /oct or full range on CH A
Left right input to left & right output
Ultra sonic -1dB @ 100k
High pass -3dB @ 40 Hz to 135 Hz, externally adjustable @ 24db /oct or full range on CH A
Power Amplifier
> 210W rms continuous
THD < 0.03% at levels up to 1dB below clip, 20 Hz - 120 Hz typ 0.005% @ 20W rms 100 Hz
Hum + Noise < -100 dB referred to clip
Controls
Crossover Frequency 40 - 135 Hz, front panel pot
Test (Band limited pink noise), front panel recessed switch (LED indicates when on)
Sub bass bypass, front panel switch (LED indicates when bypassed)
Sub Gain -14 to +6, front panel pot (Sub level indicated with LED Meter)
Sub Phase, front panel pot
Sub Polarity, front panel recessed switch (LED indication for positive and negative polarity)
Power, front panel switch
Left channel sub filter bypass, rear mounted recessed switch
Subsonic filter 14 or 28 Hz, internal jumpers
Power Requirements
Voltage Set by internal plug: nominal 115V or 230V @ 50-60Hz AC
230V setting: Min 160V (restricted output power): Max 255V
115V setting: Min 80V (restricted output power): Max 127V
Consumption
Quiescent <30W
Typical use 50W
Max <200W
Note 0dBu = 775mV into open circuit
...
Datenblatt SB 10
