Opto-compressor, three band EQ, enhancer and de-esser including digital outputs, 2U 19 "case
Shipping costs
FREE SHIPPING within switzerland!
Description
The Joemeek oneQ is the most full-featured, technologically advanced studio channel we've ever made!
A single channel combining Mic Pre (with Burr-Brown IC), four band EQ, the most flexible of any Joemeek ever, our "signature" optical compressor, De-Esser, and Enhancer, it's a master channel like no other.
Housed in a 2u chassis, the elegantly sculpted faceplate is intelligently laid out, with clear, easy to read legends and a large analog VU meter.
... We even included 24bit, 96K A / D converters with word clock input and output.
The new oneQ raises the bar for all studio master channels!
Digital Interface
The Joemeek Digital Audio Interface provides high quality digital audio outputs plus the ability to synchronize to an external word clock. The digital audio outputs are compatible with most digital recorders, as well as Digital Audio Workstations and mixers. S / PDIF format is available from the optical and RCA phono connectors, while the transformer coupled XLR connector provides to AES3 compatible output.
The Joemeek Digital Interface has highly stable onboard master clocks for low-jitter, hi-fi results. Internal sample rates of 44.1kHz, 48kHz, 88.2kHz or 96kHz are selected by means of rear panel switches. 44.1kHz is the standard used for audio CD's, while 48kHz and 96kHz are widely used in recording studios. In general, the higher the sample rate, the better the audio fidelity, but the more disk space is required for the recording. For example, recording at 96kHz requires twice as much storage as 48kHz. Consult the manual of your recorder or DAW as to what sample rates it will accommodate.
Alternatively the oneQ may be set to the frequency of an external master word clock, generated, for example, by the studio's recorder or DAW. When connected to the BNC socket provided, a suitable external word clock will be detected automatically and will override the twinQ's internal word clock.
The front panel LED labeled 'EXT CLK' illuminates when the oneQ is successfully locked to an external word clock. To avoid distortion, care should be taken not to overdrive the input to the Digital Interface. The red LED next to the Output Gain control is labeled "PEAK FSD" which stands for "Full Scale Digital". Occasional flashes are OK but if it is on all the time down, turn something!
Input Impedance:
Mic 1.2kohm:; Line: 20kohm
Pre-amp overall gain:
10dB to 60dB (variable)
Common mode rejection:
70dB
Equivalent input noise:
128.5dBu-(unweighted)
Distortion:
0.001% (below Compressor threshold)
Frequency response:
15Hz to 70kHz (-3dB)
Maximum input before clipping: Mic: +21 dBu, Line: +45 dBu
Headroom before clipping:
+21 DBu
Compressor threshold:? DBu to-20dBu (variable)
Compressor ratio:
1:1 to 10:1 (variable)
Compressor attack time: 1 msec to 100 msec (adaptive)
Compressor release time:
0.1 sec to 3 sec (adaptive)
Nominal output levels: +4 dBu/-10dBv
Output impedance:
100ohm
Output Level switch: 12dB attenuation
Noise Floor:
-85dBu (typical, with ~ 40dB mic gain)
VU Meter: Analogue movement
Power supply:
115V / 230V ac mains, 50/60Hz
Power consumption: 30W
Mechanical:
482W x 88H x 220D (overall)
Weight: 3 kilos
High Pass Filter:
12dB per octave cut below 80Hz
EQ Boost & Cut: + /-15dB (zero phase-shift bell response)
LF Frequency: 80Hz/120Hz switchable
LMF Frequency: 200Hz to 2kHz variable
HMF Frequency: 1kHz to 6kHz variable
RF Frequency: 7kHz/14kHz (selectable)
EQ "Q" 0.9 (1.6 octaves
Digital Output Specifications
Sampling:
24 Bit
Sampling rate:
44.1kHz, 48kHz, 88.2kHz or 96kHz selectable
Output format:
AES3 compliant (balanced), S / PDIF electrical, S / PDIF optical
External Word Clock input:
75ohms, 1.25V - TTL level, 44.1kHz to 96 kHz (auto synchronizing)
)
)
...
oneq_manual.pdf
